What is the purpose of a splash block?

Splash blocks are rectangular pieces of plastic or concrete placed underneath the end of the downspout. Their purpose is to direct water as far away from your home as possible while preventing the soil from eroding and causing foundation issues.

Are splash blocks necessary?

While everyone with gutters has downspouts, not all downspouts will need splash blocks. … However, any downspouts that drain above ground, especially near the building’s foundation, needs splash blocks as an added level of protection from water damage.

How do you use a splash block?

How are splash blocks installed? Install splash blocks directly under each downspout in your home capable of carrying water at least 3 feet away. Always adjust them in an angle away from your home; prepare to do some digging if needed. Tip: the ideal angle is a slope of 6 inches in 10 feet.

What is the right way to place a splash block?

Splash blocks must be set into the ground; avoid just placing them on top of the surface underneath the downspout. If the splash block is open at one end and closed at the other, the closed off edge should be against the exterior wall or flush with the foundation.

What is a concrete splash block?

Splash Blocks (Downspout Splash Guards) Precast concrete splash blocks (downspout splash guards) are placed under down spouts to allow controlled drainage of rainwater.

How do you make a splash block?

Mix one part cement with two parts masonry sand in a large bucket or cement mixer. Then add three parts limestone to the cement/sand mixture. Add water to the mixture slowly while mixing until the concrete mix achieves an oatmeal-like consistency.

What is a gutter splash guard?

They’re pieces of material that are placed in areas of a gutter system—usually valleys, also known as corners—where overspilling may occur. Furthermore, splash guards are installed on open-top gutter systems to keep water flowing through the gutter system in areas that often overflow due to heavy rainfalls.

Which way should downspouts face?

The down spout should direct water away from the foundation rather than at or along the foundation and the splash block or drain should carry water far enough away to prevent erosion at the foundation. Many builders either do not install down spout splash blocks or do not install them correctly.

How far should downspouts extend from house?

The gutters must be clean to prevent clogging. The downspouts need to be extended away from the home a minimum of four feet, with six feet being preferred. When downspouts are connected to underground drains, it is very important to keep all debris out of the gutters, downspouts and underground drains.

What does a splash block look like?

Splash blocks are devices made of plastic or concrete that channel the water away from the foundations of a building or house. They are usually rectangular, with a close-ended side positioned underneath the downspout and an open-ended side that direct the water away from the construction’s foundations.

How do you decorate a downspout?

  1. Build a Dry Creek Bed and Enhance Your Front Yard. …
  2. Make an Artistic Pebble Mosaic to Decorate Your Downspout Landscape. …
  3. Repurpose Watering Cans and Rain Gutter to Form a Wall Landscape.
  4. Decorative Splash Blocks Turn Into a Water Feature. …
  5. Build a Decorative Rain Barrel with a Planter.

How much does a splash block cost?

Splash blocks are generally under $10 per piece, although decorative cast aluminum versions can run as high as $70.

How much are cement splash blocks?

Everyday Low Price $9.99
11% Mail-In Rebate Good Through 10/9/21 $1.10

What are the things under gutters called?

Vertical pipes that lead the water from the gutter to the ground level, are known as Downspouts. In addition to that, they are also known as water spout, down pipe, drain spout, or drain pipe.

How do you stop rain splash?

  1. Check existing rain gutters to ensure they are level and there are no leaks. …
  2. Attach new rain gutters along the edge of the roof if you do not already have them. …
  3. Install drip edge flashing in addition to the gutters.

How do you hide a downspout extension?

  1. Trellises and/or Clematis Vines. This is a very decorative way to hide the ugly downspouts from top to bottom. …
  2. Blend Them with the Siding. …
  3. Rain Chain Instead of Downspout.